
Choose the feed around how the putty moves
Watch the filler at its normal inlet condition. If putty arrives steadily, a basic feed can keep the metering inlet supplied. If a stiff batch holds its shape and leaves the inlet empty, trial a matched assisted feed. Check how long the added parts take to clean and record incomplete doses over the same run.
Route 1: paste reaches the outlet steadily
1. Supply vesselPaste replenishes the outlet as material is withdrawn.
2. Compatible feed and meterA short product path supplies each dose without starvation.
3. Cut-off valveDischarge ends over the supported pail.
Route 2: thick material leaves a void at the outlet
The second route is a supply principle, not a universal putty specification. A follower plate must fit the vessel and formulation; pressure, pump, seals and hose need to suit the material. The purpose is to keep the pump inlet supplied when the paste will not move there by itself. Adding filling heads cannot correct an empty inlet.Check how the material changes after standing and during restart. Abrasive particles affect wear parts and clearances. Heating or agitation is an option only if the recipe allows it; neither should be assumed to make an unsuitable paste pumpable.1. Ram or pressure-feed unitA matched follower plate presses onto the paste and drives it towards the pump inlet.
2. Pump and connectionThe supply unit moves paste to the metering section at its required inlet conditions.
3. Meter and cut-offDosing controls the amount; the discharge valve ends the fill.
Decide how the dose will be controlled
A volumetric doser delivers a set volume. If density or entrained air changes, the same volume can give a different mass. A weighing system can either control the fill while it happens or check the result afterwards. Those are distinct jobs.| Five-kilogram pail example | Weight-controlled filling | Volumetric filling with a separate weight check |
|---|---|---|
| Before filling | Place and support the empty pail; tare it using the specified scale procedure. | Establish the pail tare for the later net-weight check and set the dosing volume. |
| During filling | Scale feedback controls the dose through the selected filling control. | Doser completes its volume-based cycle. |
| After filling | Read the settled result; use the agreed release or correction rule. | Subtract the appropriate tare and compare net content with the target. Adjust subsequent dosing or correct the pack through the specified procedure. |
A wet-putty pail from supply vessel to closed lid
Follow the container
1. Position and tareSupport the empty pail without interfering with the selected weighing arrangement.
2. Fill and cut offKeep the nozzle position and withdrawal suited to the paste.
3. Check weight and rimRead net content and inspect the lid seat before covering it.
4. Fit and close the lidUse the matching tool with support under the container.

Investigate the operation that creates the defect
| Observed problem | Likely area to examine | Useful observation |
|---|---|---|
| Weight changes after a pause | Product supply, air, settling and the metering cycle | Compare restart containers with a stable run from the same batch. |
| A strand of paste crosses the rim | Cut-off, nozzle position and withdrawal timing | Inspect the rim before placing the lid. |
| The lid does not seat evenly | Rim condition, container support and matching closing tool | Inspect the whole closure, including normal pail and lid variation. |
| Old colour appears in the next batch | Retained product in the feed and filling path | Open the agreed service points and observe the first fills after cleaning. |
Putty filling budgets with the feed scope stated
These October 2026 planning allowances concern new China-supplied equipment for one compatible wet-putty formulation and one five-kilogram pail/lid format. They assume stable supply at the specified inlet and ordinary non-hazardous operation. Dose, feed and lid trials determine output; these ranges are not quotations for an untested formulation.| Equipment allowance | Starting condition and included work | Work to price separately |
|---|---|---|
| US$6,000 to 20,000 Assisted dosing station | Putty compatible with the defined basic feed arrangement; metering, discharge controls and container support. Operators present and remove containers. The offer names the feed arrangement included. | Lid equipment if required, and any pressure-discharge system beyond the stated basic feed. |
| US$25,000 to 80,000 Automatic container filling and closing section | Stable product supply at the agreed inlet; container positioning, dosing and a specified lid-closing operation. The offer identifies lid placement, weighing and replenishment duties. | A required discharge press or other substantial upstream feed system, plus any specialist construction. |
| Project example | Complete investment structure |
|---|---|
| Putty already reaches the inlet steadily | Selected dosing or automatic filling/closing section, plus only the container and lid operations absent from that scope. |
| Putty needs pressure to leave its vessel | Matched ram/follower and pump, pressure-compatible connection and controls, then the selected filling/closing section. Price the supply unit separately against the vessel and material; add it to the section allowance rather than treating it as a minor accessory. |
