Packaging Solution

Continuously Creating Value for Society

Grease Packing Machine Price: Pails, Jars and Cartridges

A grease packing machine must supply and dose a semisolid product consistently. For jars and pails, assess pressure feeding, metering, nozzle cutoff and container support together. Grease-gun cartridges also need a dedicated holder and the closure sequence required by their construction.

For initial budgeting, allow USD 3,000 to 12,000 for a single-station, hand-loaded grease doser, USD 15,000 to 45,000 for jar or pail filling, and USD 20,000 to 60,000 for filling and closure handling of one cartridge format. These are planning allowances. Comwin specifies the product path from grease samples and container drawings.

Lubricating grease jars and pail beside closed grease-gun cartridges
Jars and pails use a different holding and closing arrangement from grease-gun cartridges. Packaging illustration.

Build the filling path around grease and its container

Try the grease at the normal start temperature and near the end of a supply drum. Only specify heated transfer if the trial shows it is needed for a steady dose or clean cutoff. Cartridge filling also needs a separate check for trapped air and the specified closure.

Grease jars and pails

Grease that does not flow reliably under gravity needs positive supply to the dosing point. A suitable pressure-feed arrangement, potentially using a follower plate, keeps the product available as its supply drum empties. The metering and nozzle arrangement must then deliver a repeatable fill without leaving a long tail across the rim.

Hand loading can suit short runs. For repeating container sizes and larger orders, assess conveyor transfer and indexed filling. Specify lid seating or pail closing as well as dosing so the filled container leaves closed. Size changes may require a different support height, nozzle or dosing range.

Grease-gun cartridge filling

A cartridge needs controlled support, the correct filling opening and a closure method matched to its construction. Define which end is supplied open, the internal piston or base arrangement, and how the final cap is seated. Check the filled cartridge in the intended grease gun or dispensing system.

Send empty cartridges, closures and grease together. Assess filling, trapped air, end sealing and dispensing as one task. A lubricant-bottle filler or cosmetic-tube sealer does not by itself specify the support and closures needed for a grease-gun cartridge.

Keep grease supply, cutoff and closure consistent

Packing problemMatched equipment or configurationHow it responds and what to checkApplicable product
Dose varies as the supply drum emptiesMatched positive-feed and metering arrangementTest near-full and near-empty supply conditions, not just the first few fills.High-consistency grease
Grease strings across the container rimSelected nozzle cutoff and controlled withdrawalInspect rim cleanliness and closure seating after consecutive fills.Open jars and pails
Cartridge has air pockets or poor dischargeSupported filling sequence and actual-use checksCompare filled mass, retained air and dispensing with the intended cartridge.Grease-gun cartridges
Changing product leaves substantial residueAccessible contact path and agreed change methodRecord recovery, disassembly and cleaning steps with the target grease.Several grease grades

Grease filling for short pail runs and repeat cartridges

Production situationFinished packStarting routeConfiguration inputs
Short production runs and several pail sizes
Closed grease jars or pailsHand-positioned pressure-fed dosingConsistency, fill mass and lid method

Add transfer when hand movement limits good output.

Repeating pails with handling bottleneck
Closed pailsMetered filling with supported container transferPail rigidity, closure load and usable output

Add transfer when hand movement limits good output.

Grease sold for grease guns
Closed cartridgesCartridge holding, dosing and end closureCartridge construction and dispensing acceptance

Change tooling when cartridge ends or internal parts differ.

Container loading, drum changes and closing work

Production modeOperator workChangeover implicationsAcceptance focus
Hand-loaded metered fillingOperator positions and closes containersUseful for short runs; actual container handling determines outputFill consistency and rim cleanliness
Conveyor-fed jar or pail fillingOperator supplies containers and closuresGuide, nozzle and support changes must be accessibleStable fills across supply levels
Cartridge filling and closing arrangementOperator supplies defined cartridge componentsFormat-specific holders and closing toolsAir-pocket, leakage and dispensing checks

Grease consistency, temperature and contact materials

Provide the grease grade, available consistency data and the temperature range expected at filling. Also send the container material, opening, target mass and permitted variation. Heating should be considered only when the formulation and supplier guidance allow it; it is not a universal cure for difficult pumping.

Assess hose, seal and contact-part compatibility with the grease formulation. Free-flowing engine oil and hydraulic oil need different delivery arrangements from semisolid grease, so equipment for those liquids still needs a grease trial. Assess unusual solvent content or hazardous-area requirements before specifying electrical and mechanical equipment.

Grease filling machine budgets

These planning ranges concern new equipment supplied from China for a defined product and format. Product preparation, extra formats, freight, taxes, overseas installation and site work are excluded unless expressly listed. Equipment additions and commercial terms are settled in the formal quotation. Special product-contact, safety or environmental requirements can change the scope.

Equipment scopePlanning budgetRange applies toItems to define separately
Hand-loaded grease dosing stationUSD 3,000 to 12,000One defined grease, supply format and single dosing positionAutomatic container transport and powered closing
Specified grease jar/pail filling arrangementUSD 15,000 to 45,000Defined feed, metering and supported transfer for one container familyAutomatic drum change and special closures
Single-format cartridge filling and closure handlingUSD 20,000 to 60,000One cartridge construction and agreed filling/closing sequenceCartridge manufacture, extra formats and complex inspection

Check supply, filling and closing at the required workload

For an illustrative batch of 1,200 pails filled to 1 kg in 240 available minutes, the requirement is 5 good pails per minute and 5 kg of grease per minute. Compare the supply, metering and closing stages against that same requirement. Use actual product trials to establish how much operating time remains after supply-drum changes and cleaning.

Weigh consecutive fills through the supply range. Inspect rims and closed packs, then check cartridge dispensing where relevant. Record product recovery from the supply drum and the contact path. A faster empty-cycle demonstration does not answer these product-handling questions.

Compare proposals on the same product and pack

DimensionEvidence to compare
Budget and scopeThe equipment operations, product and formats represented by each price.
OutputRequire the proposed supply, dosing and closure to run with the actual grease and container.
Product and format fitGrease sample, grade, consistency and filling temperature range; Container and closure samples or drawings.
SupportTraining, contact parts, spares and the responsibilities for commissioning and support.
DeliverySamples, format confirmation, layout, documentation and acceptance milestones.

Questions to settle before ordering

Can a piston filler handle every grease?

If the product can be supplied consistently and the selected seals, pressure and metering path are suitable, a configuration can be trialled. Very stiff or sensitive grease needs its own supply assessment.

Should grease be heated before filling?

If the formulation permits controlled heating, it may be assessed as part of the process. Confirm the allowed temperature and quality checks before adding heated tanks or hoses.

Can one filler cover jars and cartridges?

If the metering range and product path can be shared, some components may be common. Cartridge support and end closing remain separate tooling and handling tasks.

Is the budget a quotation for a complete line?

For a formal price, define the actual feed, containers, closing and inspection operations. The planning ranges cover the listed configuration and exclude unlisted upstream and downstream equipment.

Request a grease and container trial

Send grease and finished-container photos or samples, the fill or count, and the output you need. For the proposal, include:

  • Grease sample, grade, consistency and filling temperature range
  • Fill mass, allowable variation and target good output
  • Container and closure samples or drawings
  • Supply drum size and changeover method
  • Required lid seating, cartridge end closing or other closure work
  • Cleaning method, utilities and destination requirements

Comwin will recommend the grease supply, dosing and closing operations, explain the configuration and sample trial, and quote the agreed scope.

Comwin provides free sample testing and can arrange real factory visits. Small-equipment support includes video tutorials and remote video calls. The whole-machine warranty is two years, with three years for core components and remote response within 24 hours. Support and installation responsibilities are specified for the project.

Arrange free sample testing · Send your packing requirements

 

Table of Contents

Our packaging categories

We offer a complete range of packaging solutions.

Packing Sample
Bagged packaging
Packing Sample
Vacuum packaging
Packing Sample
Blister Packaging
Packing Sample
Filling/Bottling
Packing Sample
Heat Shrink
Case packaging
Case packaging

Get Your Quote

What delivery did you have in mind? Fill in the details below to receive a quote.