Packaging Solution

Continuously Creating Value for Society

Putty Filling Machine Price: Pails, Tins and Feed Options

A putty filling machine doses ready-mixed wet paste into pails or tins. The first question is whether the putty will reach the dosing inlet continuously. A paste that flows towards an outlet and one that holds its shape can need different supply equipment even when both go into a five-kilogram pail.An assisted dosing station has an indicative allowance of US$6,000–20,000; an automatic filling and closing section is roughly US$25,000–80,000 under the scopes below. A required pressure-feed unit adds to that investment. This guide concerns wet putty; dry powder and cartridges require other packing routes.
A closed plastic pail, closed tin and separate thick paste sample
Plastic pail and metal tin styles for wet paste (pack illustrations). Their lids require different closing tools.

Choose the feed around how the putty moves

Watch the filler at its normal inlet condition. If putty arrives steadily, a basic feed can keep the metering inlet supplied. If a stiff batch holds its shape and leaves the inlet empty, trial a matched assisted feed. Check how long the added parts take to clean and record incomplete doses over the same run.

Route 1: paste reaches the outlet steadily
1. Supply vesselPaste replenishes the outlet as material is withdrawn.
2. Compatible feed and meterA short product path supplies each dose without starvation.
3. Cut-off valveDischarge ends over the supported pail.
Route 2: thick material leaves a void at the outlet
1. Ram or pressure-feed unitA matched follower plate presses onto the paste and drives it towards the pump inlet.
2. Pump and connectionThe supply unit moves paste to the metering section at its required inlet conditions.
3. Meter and cut-offDosing controls the amount; the discharge valve ends the fill.
The second route is a supply principle, not a universal putty specification. A follower plate must fit the vessel and formulation; pressure, pump, seals and hose need to suit the material. The purpose is to keep the pump inlet supplied when the paste will not move there by itself. Adding filling heads cannot correct an empty inlet.Check how the material changes after standing and during restart. Abrasive particles affect wear parts and clearances. Heating or agitation is an option only if the recipe allows it; neither should be assumed to make an unsuitable paste pumpable.

Decide how the dose will be controlled

A volumetric doser delivers a set volume. If density or entrained air changes, the same volume can give a different mass. A weighing system can either control the fill while it happens or check the result afterwards. Those are distinct jobs.
Five-kilogram pail exampleWeight-controlled fillingVolumetric filling with a separate weight check
Before fillingPlace and support the empty pail; tare it using the specified scale procedure.Establish the pail tare for the later net-weight check and set the dosing volume.
During fillingScale feedback controls the dose through the selected filling control.Doser completes its volume-based cycle.
After fillingRead the settled result; use the agreed release or correction rule.Subtract the appropriate tare and compare net content with the target. Adjust subsequent dosing or correct the pack through the specified procedure.
A separate weight check does not automatically create closed-loop control of the filler. The feedback connection and correction method must be included if required.Container capacity is another calculation: one kilogram at 1.6 kg/L occupies 0.625 L before headspace. Actual density, filling behaviour and lid clearance determine the usable fill.

A wet-putty pail from supply vessel to closed lid

Follow the container
1. Position and tareSupport the empty pail without interfering with the selected weighing arrangement.
2. Fill and cut offKeep the nozzle position and withdrawal suited to the paste.
3. Check weight and rimRead net content and inspect the lid seat before covering it.
4. Fit and close the lidUse the matching tool with support under the container.
Two open putty pails, one with a clean lid seat and one with paste trailing across the rim
A clean lid seat and a paste strand across the rim (packaging illustration). Inspect this surface before placing the lid.
Send the lid with each container sample. The plastic pail and press-in metal lid shown above need closing tools matched to their rim and lid profiles. The proposal should identify how the container is supported, where the tool applies pressure and how full seating is checked around the closure.A trailing strand is dealt with at cut-off and nozzle withdrawal. Pressing a lid harder does not remove paste from its seating surface. Compare the last pail before a pause and the first pails after restart, when product behaviour may change.For colour changes, record paste left in the supply connection, meter and nozzle. Identify what can be recovered and which parts need cleaning. Time the change through to the first acceptable pail of the next colour; this can matter more than a faster single fill.

Investigate the operation that creates the defect

Observed problemLikely area to examineUseful observation
Weight changes after a pauseProduct supply, air, settling and the metering cycleCompare restart containers with a stable run from the same batch.
A strand of paste crosses the rimCut-off, nozzle position and withdrawal timingInspect the rim before placing the lid.
The lid does not seat evenlyRim condition, container support and matching closing toolInspect the whole closure, including normal pail and lid variation.
Old colour appears in the next batchRetained product in the feed and filling pathOpen the agreed service points and observe the first fills after cleaning.
Reactive, two-component or solvent-containing products also need their material and operating requirements defined before equipment selection. Chemical compatibility and any necessary environment-specific construction belong in the project specification.

Putty filling budgets with the feed scope stated

These October 2026 planning allowances concern new China-supplied equipment for one compatible wet-putty formulation and one five-kilogram pail/lid format. They assume stable supply at the specified inlet and ordinary non-hazardous operation. Dose, feed and lid trials determine output; these ranges are not quotations for an untested formulation.
Equipment allowanceStarting condition and included workWork to price separately
US$6,000 to 20,000 Assisted dosing stationPutty compatible with the defined basic feed arrangement; metering, discharge controls and container support. Operators present and remove containers. The offer names the feed arrangement included.Lid equipment if required, and any pressure-discharge system beyond the stated basic feed.
US$25,000 to 80,000 Automatic container filling and closing sectionStable product supply at the agreed inlet; container positioning, dosing and a specified lid-closing operation. The offer identifies lid placement, weighing and replenishment duties.A required discharge press or other substantial upstream feed system, plus any specialist construction.
Project exampleComplete investment structure
Putty already reaches the inlet steadilySelected dosing or automatic filling/closing section, plus only the container and lid operations absent from that scope.
Putty needs pressure to leave its vesselMatched ram/follower and pump, pressure-compatible connection and controls, then the selected filling/closing section. Price the supply unit separately against the vessel and material; add it to the section allowance rather than treating it as a minor accessory.
Mixing, vacuum processing, cartridge or tube equipment, labelling and cartoning are outside these scopes. Freight, taxes and overseas installation are additional unless included in the offer. These are early budget ranges, not a quotation for a confirmed formulation.

Relate kilograms per hour to container work

An illustrative demand of 1,200 kg/h equals 240 five-kilogram pails per hour, or 60 twenty-kilogram pails. The smaller pack calls for more frequent presentation and lid handling. The larger pack needs a larger individual dose and suitable support and transfer for the filled weight.Use those requirements to compare the filling, container and closing operations. They are order calculations, not predicted machine outputs. Available production time must also allow for replenishment, cleaning and format changes.

Build the scope around the paste and pail

 Send Comwin the putty sample or discharge video, the supply vessel, target weight and pail with its lid. Include the material data and colour-change pattern. The resulting proposal can identify the feed unit, dosing method and closure work, with net content, rim condition and restart behaviour as trial observations.Comwin offers free sample testing, a two-year machine warranty and a three-year warranty for core components. Remote support responds within 24 hours; installation and training are specified in the proposal.

Table of Contents

Our packaging categories

We offer a complete range of packaging solutions.

Packing Sample
Bagged packaging
Packing Sample
Vacuum packaging
Packing Sample
Blister Packaging
Packing Sample
Filling/Bottling
Packing Sample
Heat Shrink
Case packaging
Case packaging

Get Your Quote

What delivery did you have in mind? Fill in the details below to receive a quote.